例句與造句

1. Relative temperature coefficient of initial permeability
   初始磁導率比溫度系數
2. Alternating - current initial permeability
   交流初透磁率
3. The raw materials , the composition , the time of milling , the calcining temperature , the different additives , the sintering temperature and the sintering parameters were investigated . the result showed : it was advantaged to obtain high initial permeability mnzn ferrite with stable frequency characteristic using high - purity raw materials ; in order to obtain mnzn ferrite with high properties , we must control strictly the composition ; it could improve the properties of mnzn ferrite by optimizing calcining temperature . the lower calcining temperature made the permeability higher , and the higher calcining temperature could promote the frequency characteristic of permeability ; we chosen the right time of milling according to the requirement of power diameter ; in order to improve the properties of mnzn ferrite , it is necessary to add effective additives . in this dissertation , the influence of bi2o3 、 moo3 、 k2co3 、 co2o3 were investigated ; the sintering temperature , the time of heat - retaining and sintering parameters were the key factors of preparing high permeability mnzn ferrites
   研究結果表明:采用高純度的fe2o3有利于獲得高起始磁導率且頻率特性優良的鐵氧體;為了制備所需性能的鐵氧體,需要嚴格控制配方中各種原材料的含量,優化配方;由于粉體活性受預燒條件的影響,所以對不同要求的鐵氧體選擇的預燒條件就不一樣,適當降低預燒溫度有利于獲得較高的起始磁導率,而為了獲得良好的頻率特性可以適當?shù)靥岣哳A(yù)燒溫度;根據對粉體顆粒粒徑的不同需求,可以選擇不同的球磨時間;而有效的添加劑是改善材料性能的必要條件,本文在添加劑的研究中主要對bi2o3 、 moo3 、 k2co3 、 co2o3的影響分別作了詳細地討論;燒結溫度、保溫時間和燒結氣氛是高磁導率mnzn鐵氧體制備最關鍵的工藝,適宜的燒結工藝可以獲得理想微結構和組成,從而得到高性能的鐵氧體材料;而從材料的微結構上來看,要提高材料的截止頻率,就要適當?shù)丶?xì)化晶粒、增加晶粒內部的氣孔。
4. We emphatically discussed how the sintering environment affected initial permeability ( ui ) , and how different contents of zno varied saturation magnetization ( bs ) and curie temperature ( tc ) . the factors of affecting temperature stability of ferrites were analyzed . finally , we compared sol - gel auto - combustion way with conventional ceramic method
   其中重點探究了燒結條件對鐵氧體起始磁導率_ i的影響以及不同原料配方對鐵氧體飽和磁感應強度bs和居里溫度tc的影響，而且探討了溫度穩定性的產生機理及摻雜co ~ ( 2 + )對鐵氧體溫度穩定性的影響。
5. Thinning the crystal grain and increasing the center vent are effective approach to raise the limiting frequency of high permeability mnzn ferrite . through large quantities of experiments , we made progress in raising limiting frequency of high permeability mnzn ferrite . we prepared the broad band mnzn ferrite of which the initial permeability was 10000
   通過采用上述實驗中的優化配方、添加劑組合以及制備工藝,我們在高磁導率材料的寬頻特性方面取得了很大的進展,研制出了起始磁導率磁導率為10000的寬頻mnzn鐵氧體材料,當頻率達到300khz時,起始磁導率下降不到20 % ,其性能相當于epcos公司改進的t38材料。
6. It's difficult to find initial permeability in a sentence. 用initial permeability造句挺難的
7. In this dissertation , high permeability mn - zn ferrites have been prepared by the mixed - oxide route , using mn3o4 , fe2o3 and zno as the raw materials . and in this dissertation we study deeply on the preparation technology and mechanism of high initial permeability mnzn ferrite with better stability of which the initial permeability was 10000
   本文采用氧化物陶瓷工藝制備高磁導率mnzn鐵氧體,以mn3o4 、 fe2o3和zno為原料,對磁導率為10000且具有寬頻特性的高磁導率mnzn鐵氧體的制備技術和機理進行研究。